HOME | DD

ChinookCrafts — Sage Medallion Temple Plaque

Published: 2012-05-21 03:26:24 +0000 UTC; Views: 1816; Favourites: 23; Downloads: 22
Redirect to original
Description A wondeful plaque that we produced a limited run of for our Legend of Zelda Sage Medallions.

The wood is sanded, stained, and each holder is felt lined. The bottom has 6 foam feet as well so there's no scratching your surface. We only made 7 of these, and each one has found a lucky new owner at Otafest here in Calgary.

Thank you so much to everyone who picked up a set with a plaque.

-----------------------------------------------------

Etsy Store:
Chinook Crafts .
Related content

ChinookCrafts - Zelda Sage Medallions with Sage Temple Plaque

ChinookCrafts - Legend of Zelda Sage Medallions - Full Set of Six

ChinookCrafts - Rupees, more colors

ChinookCrafts - Ocarina of Time Big Key (flat view)

ChinookCrafts - Digimon Tags and Crests, interchangeable (view 1)

ChinookCrafts - Rupee Keychain, all colors

ChinookCrafts - Legend of Zelda Sage Medallions - Shadow Medallion

ChinookCrafts - Digimon Tag with Matt's Crest, Friendship (view 1)

ChinookCrafts - Pokemon Evolution Stones - Generation I (view 3)

CelestialCalista - Sage Medallions

Sarinilli - Brass Triforce Rear View Mirror Hanger

SASUU16 - legend of zelda shield

deadlanceSteamworks - Legend of Zelda Hand tooled leather belt buckle

Ryua - Hylian Shield

Jadertott - More Ocarina of Time Charms

Kattermerang - Hylian Sheilds

Enlightenup23 - LOZ Hyrule Crest Statuette

Alyboxie - Hylian Shield: Skyward Sword cosplay
Comments: 10

Mr-Pendulum [2012-05-21 18:33:32 +0000 UTC]

They look very nice! From a fellow craft to another they all hand carved and block mould or 3DPrint?

👍: 0 ⏩: 1

ChinookCrafts In reply to Mr-Pendulum [2012-05-21 19:23:19 +0000 UTC]

The Medallions were 3D print, with each reproduced after. The plaques are wooden fashioned in our garage .

👍: 0 ⏩: 1

Mr-Pendulum In reply to ChinookCrafts [2012-05-24 06:14:39 +0000 UTC]

Deadly buzz. Man how much did your 3D Printer cost? Been thinking of picking one up myself.

👍: 0 ⏩: 1

ChinookCrafts In reply to Mr-Pendulum [2012-05-24 13:14:43 +0000 UTC]

Oh lord, its not something I could afford myself. I have a good friend who assists me, and from what I understand its near $30,000-$40,000.

👍: 0 ⏩: 1

Mr-Pendulum In reply to ChinookCrafts [2012-05-24 18:35:44 +0000 UTC]

Good lord. That is expensive!
The one we have at my college is only 10K however it tends to have lines on every print.

👍: 0 ⏩: 0

Xero-Xengetsuha [2012-05-21 12:12:10 +0000 UTC]

Oh how I wish I knew about this before they were sold out. How much was it sold for?

👍: 0 ⏩: 1

ChinookCrafts In reply to Xero-Xengetsuha [2012-05-21 19:25:37 +0000 UTC]

These are so far only available at conventions due to shipping costs. But, they did sell for $55, medallions included.

👍: 0 ⏩: 1

Xero-Xengetsuha In reply to ChinookCrafts [2012-05-22 16:44:27 +0000 UTC]

I'd pay that too. In a heart beat. ^^ Now only if I had that kinda money on me though, lol. How well do they fit? Are they snug, or can I simply tilt it over and they'd just come right out?

👍: 0 ⏩: 1

ChinookCrafts In reply to Xero-Xengetsuha [2012-05-22 17:11:21 +0000 UTC]

We had two types. Both snugly fitting (to be wall mounted) which you need a butter knife to flick them out, and loose ones designed to be table top pieces.

👍: 0 ⏩: 1

Xero-Xengetsuha In reply to ChinookCrafts [2012-05-23 14:38:12 +0000 UTC]

Yeah, I would have to have a wall mounted one ^^ Does the butter knife damage them at all if you use it to flick them out at all? Or are they hard enough, something like that wouldn't scratch them?

👍: 0 ⏩: 0